The Square Platter mold from Bullseye Glass (design #8641) is a ceramic slumping form that shapes a pre-made glass blank into a square platter with a 6 inch interior floor. Place a fused or pre-cut glass piece over the mold, load it in the kiln, and gravity draws the softening glass down to conform to the shape, producing a square platter with a flat interior field and formed sides.
The outer mold footprint is 11.9 x 11.9 inches, used to confirm the form fits your kiln shelf before cutting glass. The interior forming area measures 6 x 6 x 0.6 inches deep. Slipcast from a specially formulated clay body by Creative Ceramics in Europe and imported by Bullseye Glass, this mold has a smooth surface that accepts kiln wash uniformly and holds up under repeated proper use without cracking.
What does the Square Platter mold make? It slumps a glass blank into a square platter shape with a 6 inch interior floor and about 0.6 inch sides. Size your glass to fit the interior area, fire to slumping temperature, and let gravity form the platter shape.
What size glass do I cut for this mold? The interior forming area is 6 x 6 inches, but molds are handmade and may vary slightly in size. Measure your specific mold before cutting glass rather than relying on the listed dimensions alone.
What COE glass can I use with this mold? Any COE. Ceramic slumping forms are COE agnostic, so the same mold works with COE96, COE90, or other fusible glass. Match your firing schedule to the specific glass you are using and adjust the anneal soak temperature accordingly.
How do I prep this mold before use? Coat the forming surface with a kiln wash such as Hotline Primo Primer or a shelf primer and let it dry completely before placing glass. The slipcast surface accepts kiln wash evenly. Re-coat as needed between firings.
Specifications
SKU: 164849
Manufacturer: Bullseye Glass (design #8641, item 008641; made by Creative Ceramics, imported by Bullseye)
Store model code: BG8641
Makes: one square platter per firing
Interior forming area: 6 x 6 x 0.6 in (15 x 15 x 1 cm)
Outer mold size: 11.9 x 11.9 x 0.8 in (30 x 30 x 2 cm)
Material: ceramic slumping form (slipcast clay body), reusable
Glass: any COE (COE agnostic)
Working Notes
These are guidelines, not guarantees. Every kiln fires a little differently, so test a small run first when the result matters and follow a slumping schedule suited to your glass and kiln.
Coat the forming surface with kiln wash or a shelf primer such as ZYP Boron Nitride Mold Primer , and let it dry completely before placing glass so the finished piece releases cleanly.
Molds are handmade and vary slightly in size. Measure your specific mold before cutting glass rather than relying on the listed dimensions.
Place your glass blank over the interior forming area. As the kiln reaches slumping temperature, the glass softens and gravity draws it down into the square platter shape. Visually confirm the slump during firing if your kiln allows, and pull back from temperature as soon as the glass has fully conformed.
The mold is COE agnostic. For COE90 glass, anneal around 900 F. For COE96 glass, adjust the anneal soak to about 950 F.
Let the kiln cool fully before removing the finished piece. Re-coat the mold with kiln wash as needed between firings.
Bullseye Suggested Slumping Schedule
This is a suggested starting schedule based on slumping 6mm pieces in a Paragon GL24 kiln, not a guarantee. Every kiln fires differently. Visually confirm the slump during firing and adjust the schedule for your glass and kiln.
Segment Rate (F/hr) Temp (F) Hold (min) 1 (slump) 250 1240 75 2 (anneal soak) AFAP 900 60 3 (anneal cool) 100 700 0 4 (natural cool) AFAP 70 0
AFAP = as fast as possible (kiln drops at its natural rate, door closed). Segment 2 is the anneal soak at 900 F, which is Bullseye's standard. For COE96 glass, adjust the anneal soak in segment 2 to about 950 F.
Helpful downloads: Suggested Slumping Schedules from Bullseye Glass (PDF)
Description updated: July 6, 2026
Spot an error or have feedback on this description? Report it here .